Product Search
Search results for 'T-283'
Showing 21 - 41 of 563 Total Results
(4) options
Location: Manual Compression Testing Machines
Machine custom-configured to test cubes, Accuracy of ±.5% of indicated load from 1,000 – 100,000 lbs. (11 – 1,112 kN), Choice of 3 digital load-indicating systems, Quiet-running, continuous-duty hydraulic pump . Request a Quote The CM-0100 series is based on our CM-2500 machine, custom-configured...
(4) options
Location: Volumetric Flask
Test Mark Industries supplies volumetric flasks as part of a complete line of materials testing equipment.
AA-0095
Location: Vacuum Pump
Direct-drive, two-stage, rotary-sliding, vane-high vacuum pump features a gas ballast and trap to reduce risk of oil being sucked into the system.
Density Drive Sampler, 3" ( 76.2 mm)
SA-1355
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 3" model.
Density Drive Sampler, 4" (101.6 mm)
SA-1360
Location: Density Drive Sampler
The density drive sampler from Test Mark determines in-place density of soil by driving a thin-walled tube into the soil mass to obtain a relatively undisturbed sample. 4" model.
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders. . The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of...
Speedy 2000 Moisture Tester 20 gr.
SA-0250
Location: Moisture Testing
The Speedy 2000 Moisture Tester from Test Mark is widely accepted for determining the free moisture content of a variety of materials - sand, aggregates, soil and other powders.
Pad Caps and Retainer Rings - Steel
(16) options
Location: Unbonded Capping (Retainers and Pad Caps)
Pad caps and retainer rings are available from Test Mark as part of a complete line of concrete testing equipment and supplies.
CA-4000
Location: Windsor Probe
The Windsor Probe from Test Mark evaluates the compressive strength of in-place concrete. Easy online ordering.
Automatic Loading Controlled Machines
(11) options
Location: Automatic Compression Testing Machines
Test Mark’s next generation closed-loop touchscreen controller features both full automatic and manual test control functions. Learn more.
Aqua-Check Kit, 20 gram capacity
SA-0255
Location: Moisture Testing
The Aqua-Check from Test Mark is a portable system used for measuring the moisture content of a wide range of materials including sand, aggregates and soil.
Request a free catalog of Test Mark Industries construction materials testing equipment.
AA-0120
Location: Drierite
Easily installs in-line between vacuum pump and rice test equipment. Refillable unit measures 2 5/8" by 11 3/8" with hose barbs at both ends which will accept ¼" to 3/8' flexible tubing. One of our Drierite products.
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
CA-0356-L
Location: Self-Consolidating Concrete
L-Box Flowability is a method used to determine flow rates and passibility of SCC in confined spaces. Available from Test Mark Industries.
Bench Oven, 10.6 cu. ft. 437ºF
CA-1440
Location: Bench Ovens
These bench ovens are used for curing, drying, and baking. Ovens feature high density insulation for reduced heat loss efficient operation, adjustable shelves on 1 1/2" centers, gasketed doors, and scratch resistant finish. 10.6 cu. ft. model.
CA-0289
Location: Grout Sample Box
The grout sample box from Test Mark features engineered-slotted corrugation which retains moisture while simulating CMU absorption rate.
AA-0060
Location: Sample Ejector
Asphalt Sample Ejector from Test Mark is used for removing asphalt specimens from compaction molds.